hi,
ich habe kanotix-2006-easter-rc4.
ivtv-treiber sind ja schon dabei. habe dann die firmware-dateien in "/lib/firmware" kopiert >> meckert auch nicht.
ich kann aber mit "mplayer /dev/video0" nur ein schwarzes bild sehen, also gar nix, kein signal rauschen o.ä.
in den ivtv-meldungen wird auch ein fehler mit i2c hardware gemeldet. damit kann ich leider nichts anfangen.
hier mal der auszug:
Code:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.6.2 (tagged release) loading
ivtv: Linux version: 2.6.16.16-kanotix-1 SMP preempt 586 gcc-4.0
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 169
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[169] MMIO=[f7005000-f70057ff] Max Packet=[2048] IR/IT contexts=[4/8]
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 193
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xfb000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 4-2: new low speed USB device using uhci_hcd and address 2
tveeprom 1-0050: Hauppauge model 48139, rev K257, serial# 8260564
tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
usb 4-2: new low speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
epic100.c:v1.11 1/7/2001 Written by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/epic100.html
(unofficial 2.4.x kernel port, version 1.11+LK1.1.14+AC1.1.14, June 2, 2004)
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00508d000072023d]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
ts: Compaq touchscreen protocol output
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c addr 0x40 not found for command 0x40086d11!
ivtv0: i2c addr 0x40 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv: ==================== END INIT IVTV ====================
was kann ich da tuen? wer kann mir bitte helfen, würde so gerne mythtv benutzen  |